brocade command

*************************************

設定固定 mac address

static-mac-address d461.3700.8ef9 drop

*********************************

查看 10G port 版權

sh license

sh ver

************************************

telnet@prac2-8F#sh chassis

The stack unit 1 chassis info:

Power supply 1 (NA - AC - Regular) present, status ok

Power supply 2 not present

Fan 1 failed

Fan 2 failed

Fan 3 failed

telnet@Sport-B#sh chass

  chassis                Power supply/fan/temperature

telnet@Sport-B#sh chassis 

Power supply 1 (NA - AC - Regular) present, status ok

Power supply 2 not present

Fan ok, speed (auto): 1<->[[2]]<->3

Fan speed switching temperature thresholds:

1 -> 2 @ 50 deg-C

1 <- 2 @ 40 deg-C

2 -> 3 @ 55 deg-C

2 <- 3 @ 50 deg-C

Sensor B Temperature Readings:

Current temperature : 49.5 deg-C

Warning level.......: 85.0 deg-C

Shutdown level......: 90.0 deg-C

Sensor A Temperature Readings:

Current temperature : 49.0 deg-C

Boot Prom MAC: 0024.38cb.82c0

Management MAC: 0024.38cb.82c0

telnet@Sport-B-B1F-research#sh chassis 

Power supply 1 (NA - AC - Regular) present, status ok

Power supply 2 not present

Fan ok, speed (auto): [[1]]<->2<->3

Fan speed switching temperature thresholds:

1 -> 2 @ 50 deg-C

1 <- 2 @ 40 deg-C

2 -> 3 @ 55 deg-C

2 <- 3 @ 50 deg-C

Sensor B Temperature Readings:

Current temperature : 45.0 deg-C

Warning level.......: 85.0 deg-C

Shutdown level......: 90.0 deg-C

Sensor A Temperature Readings:

Current temperature : 40.0 deg-C

Boot Prom MAC: 0024.38cb.9840

Management MAC: 0024.38cb.9840

*************************************************
ruckus sgz
sz active-list 203.68.0.215
********************************************
開通 icmp
no ip icmp unreachable

*************************************************
選擇 boot image
#sh flash
#boot sys flash primary

#sh boot-preference
Boot system preference(Configured):
Use Default

Boot system preference(Default):
Boot system flash primary
Boot system flash secondary

**************************************************
sh mac addresss fan 溫度

sh chassis

mac addresss 可查看機器後面貼紙


***************************************************************
show brocade cpu command

sh cpu
**********************************************************************************
upgrade_brocade_icx6450_poe_fireware

指令如下：
Syntax: inline power install-firmware [stack-unit |unit-number] tftp ip-address

filename
ex:
 inline power install-firmware stack-unit 1 tftp 192.168.12.150 xxxx.fw

telnet@act-a-b1#sh module
       Module                                         Status Ports Starting MAC
U1:M1  ICX6450-24p POE 24-port Management Module        OK     24   748e.f8b0.aa60
U1:M2  ICX6450-SFP-Plus 4port 40G Module                OK     4    748e.f8b0.aa79

ICX-6450 unit-number  1: poe 24 port  2: 4port 40G


**********************************************************************************
show tech
***********************************************************************************
showbrocade snmp community(顯示brocade snmp community)
enable password-display
show snmp server

snmpwalk -c *****  -v 2c 192.168.27.252 |grep IP-MIB::ipNetToMediaIfIndex

Response:

IP-MIB::ipNetToMediaIfIndex.1.192.168.24.4 = INTEGER: 1

IP-MIB::ipNetToMediaIfIndex.1.192.168.24.5 = INTEGER: 1

IP-MIB::ipNetToMediaIfIndex.1.192.168.24.7 = INTEGER: 1

IP-MIB::ipNetToMediaIfIndex.1.192.168.24.14 = INTEGER: 1

IP-MIB::ipNetToMediaIfIndex.1.192.168.24.15 = INTEGER: 1

IP-MIB::ipNetToMediaIfIndex.1.192.168.24.16 = INTEGER: 1

**************************************************************
測試 cable 長度

Brocade# phy cable-diag tdr 1/1/1

Brocade# show cable-diag tdr 1/1/1

telnet@FWS624 Switch#phy cable-diagnostics tdr 0/1/1
telnet@FWS624 Switch#
telnet@FWS624 Switch#show cable-diagnostics tdr 0/1/1

Port Speed Local pair Pair Length Remote pair Pair status
---- ----- ---------- ----------- ----------- -----------
0/1/1 UNKWN Pair A     0000086M             Open    
        Pair B     0000089M             Open    
        Pair C     0000088M             Open    
        Pair D     0000084M             Open    
telnet@FWS624 Switch#


ip-multicast-disable
 broadcast limit 8192
 unknown-unicast limit

Viewing broadcast, multicast, and unknown unicast limits
You can use the show run interface command to display the broadcast, multicast, and unknown-unicast limits configured on the device.

You can use the following commands, in addition to the show run interface command, to display the broadcast, multicast, and unknown-unicast limits configured on the device:

show rate-limit unknown-unicast
show rate-limit broadcast

Use the show run interface command to view the broadcast, multicast, and unknown-unicast limit configured on each port.

Device# show run interface
interface ethernet 4
broadcast limit 1245184 bytes
multicast limit

Device# show rate-limit multicast

Multicast Rate Limit Settings:
 Port          Limit   Packets/Kbps
 1/1/30          96        Packets

Device# show rate-limit broadcast
Broadcast/Multicast Limit Settings:
Port    Limit   Packets/Bytes   Packet Type(s)
4     1245184           Bytes   Broadcast + Multicast
5     1245184           Bytes   Broadcast + Multicast
14      65536         Packets   Broadcast only
23     131072         Packets   Broadcast + Multicast
Sample output - ICX 6650 devices


**********************************
fw624 forget password
*******************************

Follow the steps given below to recover from a lost password.
1. Start a CLI session over the serial interface to the device.
2. Reboot the device.
3. At the initial boot prompt at system startup, enter b to enter the boot monitor mode.
4. Enter no password at the prompt. (You cannot abbreviate this command.) This command will
cause the device to bypass the system password check.
5. Enter boot system flash primary at the prompt.
6. After the console prompt reappears, assign a new password.

**********************************************************************